
Scalable fogging system with timer control.
- Draws from pre-mixed solution
- Powered by compressed air and electricity
- Quick-change pump
- Single shot timer with delay on make
- With FG-NA-N130 nozzle assemblies:
- Droplet size: 15 microns at 50 psi (3.4 bar)
- Polypropylene and Kynar nozzle construction
- Up to 20 nozzles per control box
- With FG-NA-26SS nozzle assemblies:
- Droplet size: 35 microns at 50 psi (3.4 bar)
- Celcon, stainless steel, EPDM, and nylon nozzle construction
- Up to 12 nozzles per control box
Datasheet
Wall Mounted Fog System
User Manual
Wall Mounted Fog System
Questions?

- POWER TYPE
Compressed air, electricity
- CHEMICAL PICKUP TYPE
Draws from pre-mixed solution
- NUMBER OF PRODUCTS UNIT CAN DRAW FROM (AND WHETHER IT DRAWS SIMULTANEOUSLY OR ONE AT A TIME)
One product
- SUCTION LINE LENGTH/DIAMETER
8 ft. (2.4 m) hose with 3/8 in. (9.5 mm) inside diameter
- FLOW RATE*
WITH FG-NA-N130 NOZZLES: 7.9 oz/min (0.23 l/min)
WITH FG-NA-26SS NOZZLES: 5.3 oz/min (0.16 l/min)
- PUMP SEALS
Santoprene, Viton, or Kalrez
- NOZZLE CONSTRUCTION
WITH FG-NA-N130 NOZZLES: Polypropylene and Kynar
WITH FG-NA-26SS NOZZLES: Celcon, stainless steel, EPDM and nylon
- TIMER OPERATION TYPE
Delay on make single shot
- DROPLET SIZE
WITH FG-NA-N130 NOZZLES: 15 microns at 50 psi (3.4 bar)
WITH FG-NA-26SS NOZZLES: 35 microns at 50 psi (3.4 bar)
- COVERAGE AREA
1 liter of solution will cover approximately 1000 cubic feet**
- COVERAGE PATTERN
WITH FG-NA-N130 NOZZLES: Flat pattern with projection up to 10 ft. (3 m) from nozzle
WITH FG-NA-26SS NOZZLES: Pattern up to 8 ft. (2.4 m) wide (side to side) and 3 ft. (0.9 m) thick (top to bottom), with projection up to 15 ft. (4.6 m) from nozzle
- NUMBER OF NOZZLES***
WITH FG-NA-N130 NOZZLES: 1-20 nozzles per control box
WITH FG-NA-26SS NOZZLES: 1-12 nozzles per control box
- TUBING/FITTING SIZES
Designed for use with 3/8 in. (9.5 mm) outside diameter tubing between control box and nozzle(s)
*Dilution rates and flow rates given are based on chemical with viscosity of water and factory air pressure settings.
**Area covered and run time may vary based on humidity, air flow, and product used.
***Number of nozzles is dependent upon air supply (see Compressed Air Requirements)
- COMPRESSED AIR REQUIREMENTS
WITH FG-NA-N130 NOZZLES: At factory air pressure setting of 50 psi (3.4 bar): 2 cfm (56.6 l/min) for control box, plus 2.5 cfm (70.8 l/min) per nozzle
Maximum incoming air pressure: 150 psi (10.3 bar)WITH FG-NA-26SS NOZZLES: At factory air pressure setting of 50 psi (3.4 bar): 2 cfm (56.6 l/min) for control box, plus 5 cfm (142 l/min) per nozzle
Maximum incoming air pressure: 150 psi (10.3 bar)- LIQUID TEMPERATURE RANGE
40-100˚F (4.4-37˚C)
- ELECTRICAL REQUIREMENTS
120 VAC at 60 Hz, 2 amps (GFCI protected outlet)
- OPERATING VOLTAGE
120 VAC
- CHEMICAL COMPATIBILITY
Chemical products used with this equipment must be formulated for this type of application and compatible with unit materials and pump seals. For more information on chemical compatibility, consult the manufacturer or SDS for your product or contact our customer service department.
- Item number FOG-IT6 includes: Complete control box, clear tubing (200 ft. (60.9m) of 3/8 in. (9.5 mm) outside diameter tubing), mounting hardware, and user manual
- Item number FG-NA-N130 includes: Complete nozzle assembly, mounting hardware, and user manual
- Item number FG-NA-26SS includes: Complete nozzle assembly, mounting hardware, and user manual
FAQs
Which pump seal material should I choose?
Pump Seal Material Compatibility
Choose a pump seal material that is compatible with the chemicals you will use. Chemical incompatibility can cause accelerated wear and equipment failure that is not covered by warranty, so it’s important to do your research.
- Consult the safety data sheet (SDS) for your chemical to learn about the ingredients.
- Use a chemical compatibility database (like this one: https://www.coleparmer.com/Chemical-Resistance) to look up the ingredients and find material compatibility info.
- Note that the concentration of chemicals makes a big difference in compatibility. Think about whether the chemical you use will be in a pre-diluted or concentrated form when it is used in the equipment.
- If you need help, ask your chemical manufacturer. Or, send your SDS to techsupport@foamit.com and we can help.
Accessories

Wondering How to Buy?
We have distributors all over the world. Tell us a little bit about you and your equipment needs, and we’ll help you find or become a distributor.